SaabCentral Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 67 Results
  1. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hey there, so I recently replaced my coils and spark plugs and now the car won’t start. Coil 4 melted to the connector so I rewired a new connector and connected it to the new coil. The car won’t turn over. I also lifted my battery tray out and cleaned my ground points as well as put in an...
  2. NG900 & OG9-3 Performance, Mods & Tuning
    Hey, So I’m putting a 2.0l engine from a 95 900se into a 95 900s. The main issue that’s looming over my head is that the engine im dropping in is dic and the old engine is distributor. Obviously a new ecu or a tune and I’m getting a ecu from Abbottsaab.com but how would I plug in the ignition...
  3. NG900 & OG9-3 Workshop
    Hi all! I'm back at the forum to make my second post :) Edit: I've mistakenly called ISO connectors for DIN connectors. I have since edited the correct word in. Thanks Mimmi for correcting me! :) So, I recently found out after removing RH interior door panel that my 2002 Saab 9-3 Convertible...
  4. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hello all, mistakes have indeed been made during my bypass audio installation in my 2006 9-3 (sedan, ICM2). Essentially, the wires that connected to pins 1-8 on my ICM2 got cut and detached from the harness. This means that I have no idea which pins each wire from the loom is supposed to go to...
  5. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I have 2008 1.9 tid 150bhp. Front right fog light is always on even with ignition off and key out. But there's an error front right fog failure on sid. Left fog light comes on and off when I press button for them. Fuses are fine bulbs are brand new. I disconnected light switch in dash and...
  6. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I am thinking of putting on an electric cutout on my '03 9-3 2.0t. The only spot that I could really put it is after the resonator but I'm afraid that it will dampen the turbo sound. I'm also worried about wiring it to the fuse box and blowing a fuse but if I were to wire it to the battery then...
  7. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Alright im working on my 04 9-3. About 2 weeks ago I got put in limp mode for a p2138. iv read I think almost every post on here in regards to the code with no luck. So far I have removed the 2 connectors under the batter and soldered each wire together and heat shirnked that did nothing even...
  8. 9000 Workshop
    Hello its me again! With another problem... I have mentioned in another post about changing to aero seats in my 9000 and them draining my battery, I found a fix but there is still some weird electrical problems. So basicaly the light for the right door stays on but is very dim and can only be...
  9. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hi all, I'm nearly stuck on my search for the cause of a mystery misfire in cylinder 1 of my 2007 Saab 9-3 Aero 2.8L Manual... My BlueDriver code reader is spitting out P0201 and P0301, and after replacing the cylinder 1 coil and plug, all the injectors, and performing countless tests, I have...
  10. C900 Workshop
    The fuel pump runs when I jump the 27 top and 30 bottom fuses. However, when the fuses are in and I try to start the car the pump doesn't run. The fuel and system relays were tested, and can be felt to be working when plugged in and the car is powered on. (The ignition was replaced with...
  11. C900 Workshop
    I'm failing to find a list or diagram indicating which wires connect to what in the 29-pole (or 29-pin) bulkhead connectors. I have Bentley's and PDFs of the shop manuals, but have yet to find a clear list. It would be great to have simple images and/or lists for the different years, and...
  12. C900 Workshop
    I'm cross-posting a thread from a different site in the hope of more activity here. Hope that's okay. Long story short, the wiring to the ignition and fuel pump have been mucked with. Badly. Long, long ago (after the ignition switch broke) a friend put in a contact switch and an off/on...
  13. 9-5 Workshop
    I recently installed a trailer hitch on my 2006 9-5 wagon and am now looking to install the wiring for some trailer lights. I've read the posts about the older 9-5's having the wiring harness in the rear hatch area, however, because mine is a later model, it didn't come with the 10 pin...
  14. 9000 Workshop
    both front power windows in my 92 9000s have stopped working. have checked all fuses inside glove box compartment, took apart the center console switches and cleaned them, installed new regulator on driver side, still not working. They seemingly have no power at all when testing them with volt...
  15. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Found an interesting site that seems to have a plethora of wiring diagrams for many makes and models that is searchable: https://www.revbase.com/BBBMotor/Wd I did check and it has wiring diagrams for my 2004 9-3. Just passing it along.
  16. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hello all! I have been battling door actuator issues with my '08 9-3 Aero. I replaced the driver side and rear driver side actuators, and they are working great. I moved over to the rear passenger side, got the door all torn apart, the window removed, to find that the actuator was not...
  17. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hey folks, I've probably tried to run this question by before but I can't find it. I've got a 04 9-3 Aero and Installed and programmed an ACC unit with heated seats and swapped both front seats from an 06 that had heated seats from the factory. After quite a bit of research, I've learned...
  18. 9-5 Workshop
    Hi folks, I have a 2004 9-5 Aero. Many years ago, the driver's side seat heater would get super hot in one particular area of the seat. So hot, that you would have to turn off the heater as it would probably burn you or burn a hole in the seat. I've read that this problem is likely caused by...
1-19 of 67 Results
Top