SaabCentral Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 104 Results
  1. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Had my saab 93 ttid 6 speed manual a few months now and wandering if the problem I'm having is normal. Clutch seems to be fine and pulls away fine but when changing gears and lifting the clutch it is harsh especially 3rd can also be a little stiff to get in some gears mainly 2 and 3 if this...
  2. Parts for Sale/Wanted - North America
    I’M LOOKING FOR A SUBFRAME FOR MY 2011 9-3 AWD TURBO. ANY SUGGESTIONS? THANK YOU
  3. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    If you have been having issues with the convertible soft top on your Saab 9-3, I feel your pain! I have taken it to multiple repair shops, (including a Saab Dealership) and have had no solutions besides pay $800 for new hydraulic motor, and recommended me to just stick with the manual way to...
  4. NG900 & OG9-3 Workshop
    Mounted an interior heater bracket for the winter in my Saab 9-3 98', and I'm a little afraid I might have hit a wire with the screws. Feels highly unlikely, since I used screws shorter than 2cm, but thought I'd ask here anyways. After installing the bracket my blower fan stopped working the...
  5. New Member Introductions
    Hello everyone! We are two brothers who love Saab! We like to develop, improve and make our saabs more fun to use. Some of you may have already seen some things we have done such as cup holders and USB chargers. You are welcome to check out our website Hem | Saab3dPrint and follow our...
  6. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I'm finally finishing up this project and I labeled everything except this one bolt and one connector and of course now I can't remember where they go. The bolt, I don't even remember removing it, but I had it on my battery case/holder that I removed so I think it is from that area. It is size...
  7. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Howdy, first time on a forum so excuse me if I somehow mess this up. I’m having an issue where the radio, A.C, and all the lights inside/outside work fine when I turn the ignition on, but there’s no crank or start. The battery is good at 12.4v (also load tested it). The starter is new (just...
  8. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I believe the max hp you make on the stock block is just over 300 but im not sure can someone let me know.
  9. NG900 & OG9-3 Workshop
    So, I noticed today that the top left connection of my ABS pump has started to leak. I cleaned the top of the pump, went for a drive, and when I got back this was what I saw. Is there an easy way of fixing this instead of getting a brand new ABS pump? Is there an O ring / Seal underneath the...
  10. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hi! Recently I have noticed that in lower gears (2 and 3) the car sometimes pulls strongly to the right while driving. Anyone else experience something similar? I have had the wheels balanced and tested - all fine. The car has been to the garage/mechanics twice and they can't identify the...
  11. NG900 & OG9-3 Workshop
    So I tried adjusting the right side handbrake "cog" inside the rear brake rotor because the right side is bad when pulling the handbrake. I pushed the cog upwards, and now my handbrake is much worse than before, and I can pull it all the way up without any resistance. It does lock, but only at...
  12. NG900 & OG9-3 Workshop
    So I recently replaced my thermostat, because my engine temp was always at the lowest when driving on a motorway, and in city traffic it would fluctuate a lot. Replacing the thermostat fixed the issue, well I thought it did. It warmed up really well, and stayed in the middle of the temp gauge...
  13. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I have a 2005 Saab 93 2.0T. When I press on the gas white smoke comes out. Starts up right away. Turbo is good. I had a code P0300 like 4 days ago but it went away. No check engine light. Even with scanning it.
  14. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hey, gang! In the market for new front struts. Would prefer a quick strut if possible for easier install. Any recommendations? 05' 9-3 ARC
  15. 99 & 90 Workshop
    Just replace the clutch, pressure plat, slave, and clutch master cylinder a couple of months ago. Now I still have pedal, and it feels like the shifter is shifting into gear. However, the car wont engage and i can let off the clutch in any gear without stalling. It's like its stuck in neutral.
  16. New Member Introductions
    So hello, I am introducing myslelf today... Gary Fox, proud owner of a Saab 9-3 on an 04 plate, done 100,000 miles and has been on a SORN for 3 years now. I am looking to get the car back on the road and need a couple of questions answered hence the sign up. I look forward to hearing from you...
  17. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hey, I replaced my starter motor today and moving some of the pipes that was in the way, one snapped. I am not too sure of what that is. The pipe snapped right by a small part (pls see pics) The inlet coming from the engine expulse air through that pipe and following the pipe,it then goes...
  18. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Dad bought a car that didnt run and had no clutch. Cars running now replaced the clutch and clutch master cylinder along with the slave and throwout bearing. The car shakes very badly at all speeds.. guessing thats unrelated. Itll shift through all the gears without a problem but once you hit 55...
  19. Cars Wanted - North America
    Hi, I'm searching for basically any SportCombi with a MT around Dallas (I'll go to surrounding states, out to around Mississippi) for under $5k as a high school project. I'll be watching the post, so just reply on here if you're considering selling yours or know where one may be. Thank y'all so...
1-19 of 104 Results
Top