SaabCentral Forums banner
evap
1-13 of 13 Results
  1. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I have a 2006 9-3 2.0T with the p1452 I replaces the fuel tank pressure sensor has a newer fuel pump also. Code still comes back I have checked pretty much everything my plug for FTP is reading fine I believe with the meter purge valve is newish I think and I had it smoked and they say it was...
  2. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Recently after buying my 09' 9-3 aero XWD I have been fighting to get the car a state inspection because of a Check Engine Light. I am getting code P0089 "Fuel regulator efficiency" and have been doing research. I have checked fuel pressure to be in spec, there are no drivability issues in the...
  3. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hi everyone, B284 engine I have searched this site and can't find anything regarding this DTC Just a general google search is pointing me to evap purge solenoid high voltage, but I am not sure if this is vehicle specific. No other codes. Can't find this DTC on the WIS either. Last year, I...
  4. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hello Everyone. I am trying to resolve p0449- "EVAP system vent valve solenoid is malfunctioning" I already replaced "EVAP Purge valve: and gas cap but the code didnt get cleared. Next I will try to replace Canister valve Solenoid. Looks like both the canister and the valve near the gas...
  5. NG900 & OG9-3 Workshop
    Hi. I have three CEL codes P0444, P1312, and P1334 on my car. I have a 2001 9-3 SE. The 1312 and 1334 I have seen as being misfires in cylinders 1+2 and 3+4. I have also been told these two codes can be fixed by getting a new DIC. I have replaced my DIC 4 times with this car and these codes...
  6. Saab 9-2X, 9-4X & 9-7X Workshop
    Hi I recently did some work to my 2007 Saab 9-7x. 5.3 v8, 118-000 km. I was receiving a code for the Throttle Positioning sensor (TPS) being Off. Check Engine light On. No other codes at the time. After some reading, and my mechanics advice to remove the throttle body and cleaning it to see...
  7. NG900 & OG9-3 Workshop
    Ok. I give up. I've looked and can't find it. I've replace the one on my son's 2001 9-3. That was easy. Can't find that damn thing on mine. I did notice the manufacture date of my 9-3 is 04/98 if that matters. My 9-3 is a 5 speed manual and has the older 2.0T engine. Any help would be...
  8. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    Hi everyone! I hope everyone had a great start to 2015! :) My 2006 9-3 Aero recently threw a P0496/P2187 code and figured it was time to change the EVAP purge valve. I live in a place where there aren't many shops that work with European cars (there's one a little drive away, but they charge...
  9. 9-5 Performance, Mods & Tuning
    It was a nice sunny day with blue skies ,in Nirthen CA and I was Spiriting away my 9-5 at 95 ! ...no one looking Over me ,when all of a sudden bad luck dwelled On me ,withoutkich warning .Check engine light Came on sparsely initially and then the car started Acting funny . It refused to pick...
  10. NG900 & OG9-3 Workshop
    Hi I recently bought a 2001 Saab 2.0 turbo hatch back. Car is in excellent condition with a new PCV upgrade kit to prevent future sludge. My problem is the engine light. I have my own diagnostic and keep coming up with the same code P0440 evaporative emission control system malfunction. Is there...
  11. 9-3 Sedan, Cabrio '04+, Combi, 9-3X Workshop
    I was changing my spark plugs on my V6 and unfortunately broke an EVAP line. It was a small hard plastic piece. it was on the other end of the hose that runs from the back side of the intake down to the right side of the intake near the turbo. But i cant seem to find anywhere what the heck this...
  12. NG900 & OG9-3 Workshop
    Another interesting turn of events for my goose. Good News: After some fiddling and a bit of WD-40, the microswitch for my top decided it wanted to play nice again, and started to work in the middle of a 30 mile commute this week. No more irritating SID chimes, for now. Removed the rear...
  13. NG900 & OG9-3 Workshop
    Howdy. I recently replaced the fuel pump on my 2001 9.3 SE and have since thrown a CEL at startup with code PO453 "evap control system pressure high, sensor" I've checked for a pinched evap line, as well as the routing of the feed and returns. All appears fine. The car runs great, but I can...
1-13 of 13 Results
Top